How to Add a New Hard Disk Without Rebooting on CentOS 7/ RHEL 7

Share this Article :

Normally when you have added new storage to a running Virtual machine, you probably won’t see the new storage automatically.

This is because the SCSI bus to which the storage devices are connected needs to be rescanned to make the new hardware visible.

As a system administrator, to maintain the linux server uptime is very important and it is better to add a new hard disk without reboot the server.

There is one simple command to rescan the SCSI Bus and add SCSI Devices. The command will trigger the linux rescan scsi bus device on the system.

The following steps has been tested on CentOS 7, RHEL 7 and Oracle Linux 7.

Steps to Add a New Hard Disk Without Rebooting on CentOS 7/ RHEL 7

1. Add the new 20GB vdisk from the ESXi or vCenter :

Add a New Hard Disk Without Reboot

2. Show current disk and partition :

[[email protected] ~]# fdisk -l
Disk /dev/sda: 32.2 GB, 32212254720 bytes, 62914560 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: dos
Disk identifier: 0x0006b96a

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *        2048     1026047      512000   83  Linux
/dev/sda2         1026048    62914559    30944256   8e  Linux LVM

Disk /dev/mapper/centos-swap: 2147 MB, 2147483648 bytes, 4194304 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mapper/centos-root: 29.5 GB, 29536288768 bytes, 57688064 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes

3. Identify host bus number :

[[email protected] ~]# ls /sys/class/scsi_host/
host0  host1  host2

4. Rescan the SCSI Bus to Add a SCSI Devices :

[[email protected] ~]# echo "- - -" > /sys/class/scsi_host/host0/scan
[[email protected] ~]# echo "- - -" > /sys/class/scsi_host/host1/scan
[[email protected] ~]# echo "- - -" > /sys/class/scsi_host/host2/scan

4. Verify the disk and partiton and make sure 20GB has been added. In this case, the following line appeared “Disk /dev/sdb: 21.5 GB, 21474836480 bytes, 41943040 sectors” and confirmed that 20GB has been added without reboot the server :

[[email protected] ~]# fdisk -l

Disk /dev/sda: 32.2 GB, 32212254720 bytes, 62914560 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: dos
Disk identifier: 0x0006b96a

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *        2048     1026047      512000   83  Linux
/dev/sda2         1026048    62914559    30944256   8e  Linux LVM

Disk /dev/mapper/centos-swap: 2147 MB, 2147483648 bytes, 4194304 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mapper/centos-root: 29.5 GB, 29536288768 bytes, 57688064 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/sdb: 21.5 GB, 21474836480 bytes, 41943040 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes

Leave a Reply